Building Techoclogy » wood

Wood-plastic composite

blogtopia — Wed, 03 Jun 2009 06:42:57 +0000

Wood-plastic composite (commonly abbreviated as WPC) is a non-recyclable composite material lumber or timber made of recycled plastic and wood wastes.

There are also application in the market, which utilize only virgin raw materials. Its most widespread use is in outdoor deck floors, but it is also used for railings, fences, landscaping timbers, cladding and siding, park benches, molding and trim, window and door frames, and indoor furniture.

Manufacturers claim that wood-plastic composite is more environmentally friendly and requires less maintenance than the alternatives of solid wood treated with preservatives or solid wood of rot-resistant species. Resistant to cracking and splitting, these materials can be moulded with or without simulated wood grain details. Even with the wood grain design these materials are still visually easy to distinguish from natural timber as the grains are the same uniform color as the rest of the material. Well-known trade names include Practiwood, NewTech, TimberTech, Trex, JER Envirotech, CorrectDeck, Artowood, Chylon, Ultradeck and Weatherbest.

Wood-plastic composite is still a very new material relative to the long history of natural lumber as a building material but can be substituted in most instances. Although being highly resistant to rot, Wood Plastic Composites still soak up water due to their mixing with organic wood fibers.

Wood-plastic composite lumber is composed of wood from recovered saw dust (and other cellulose-based fiber fillers such as pulp fibers, peanut hulls, bamboo, straw, digestate, etc.) and virgin or waste plastics including high-density polyethylene, PVC, PP, ABS, PS and PLA.

Source: Wikipedia

Multilaminar veneer

blogtopia — Wed, 03 Jun 2009 06:37:58 +0000

Multilaminar wood veneer uses plantation wood to reproduce decorative effects which are typical of quality wood species (often protected and rare). This aids the preservation of biodiversity and complies with the principles of Sustainable forest management.

Large sheets of veneer are produced on a machine similar to a lathe. The sheets are dyed, then compressed and bonded into thick (typically 70cm) logs. These logs are then sliced to create the end product. If the sheets are compressed between plattens with an undulating surface, the slice will cross several layers and produce a patterned effect. Many different finished designs can be obtained by varying the plattens, dyes and stacking order.

ALPILIGNUM is the exclusive multilaminar wood veneer produced by ALPI SPA by glueing, pressing and slicing sheets of dyed wood. It offers almost unlimited scope for producing colours and grains that reproduce high-quality woods as well as creative textures. Using raw materials originating from environmentally managed forests and from agricultural plantations, Alpi technicians reconstruct high-quality woods through a precise industrial process, offering the furniture industry a top-quality semi-finished product with dimensional and physical/mechanical characteristics superior to those of natural products. The process also maintains the utmost respect for the environment.

Source: Wikipedia

Heartwood and sapwood

blogtopia — Tue, 02 Jun 2009 07:07:22 +0000

Heartwood is wood that has become more resistant to decay as a result of deposition of chemical substances (a genetically programmed process). Once heartwood formation is complete, the heartwood is dead. It appears in a cross-section as a usually colored circle, usually following the growth rings in shape. Heartwood may be much darker than living wood. However, other processes, such as decay, can discolor wood, even in woody plants that do not form heartwood, with a similar color difference, leading to confusion. Some uncertainty still exists as to whether heartwood is truly dead, as it can still chemically react to decay organisms, but only once (Shigo 1986, 54).

Sapwood is the younger, outermost wood; in the growing tree it is living wood, and its principal functions are to conduct water from the roots to the leaves and to store up and give back according to the season the reserves prepared in the leaves. However, by the time they become competent to conduct water, all xylem tracheids and vessels have lost their cytoplasm and the cells are therefore functionally dead. All wood in a tree is first formed as sapwood. The more leaves a tree bears and the more vigorous its growth, the larger the volume of sapwood required. Hence trees making rapid growth in the open have thicker sapwood for their size than trees of the same species growing in dense forests. Sometimes trees (of species that do form heartwood) grown in the open may become of considerable size, 30 cm or more in diameter, before any heartwood begins to form, for example, in second-growth hickory, or open-grown pines.

The term heartwood derives solely from its position and not from any vital importance to the tree. This is evidenced by the fact that a tree can thrive with its heart completely decayed. Some species begin to form heartwood very early in life, so having only a thin layer of live sapwood, while in others the change comes slowly. Thin sapwood is characteristic of such species as chestnut, black locust, mulberry, osage-orange, and sassafras, while in maple, ash, hickory, hackberry, beech, and pine, thick sapwood is the rule. Others never form heartwood.

Source: Wikipedia

Wood Formation

blogtopia — Tue, 02 Jun 2009 07:01:39 +0000

Wood, in the strict sense, is yielded by trees, which increase in diameter by the formation, between the existing wood and the inner bark, of new woody layers which envelop the entire stem, living branches, and roots. Technically this is known as secondary growth; it is the result of cell division in the vascular cambium, a lateral meristem, and subsequent expansion of the new cells.

Growth rings
Knots
Heartwood and sapwood

Source: Wikipedia

Different woods

blogtopia — Tue, 02 Jun 2009 03:50:44 +0000

There is a strong relationship between the properties of wood and the properties of the particular tree that yielded it. For every tree species there is a range of density for the wood it yields. There is a rough correlation between density of a wood and its strength (mechanical properties). For example, while mahogany is a medium-dense hardwood which is excellent for fine furniture crafting, balsa is light, making it useful for model building. The densest wood may be black ironwood.

It is common to classify wood as either softwood or hardwood. The wood from conifers (e.g. pine) is called softwood, and the wood from dicotyledons (usually broad-leaved trees, e.g. oak) is called hardwood. These names are a bit misleading, as hardwoods are not necessarily hard, and softwoods are not necessarily soft. The well-known balsa (a hardwood) is actually softer than any commercial softwood. Conversely, some softwoods (e.g. yew) are harder than most hardwoods.

Engineered wood products have properties that usually differ from those of natural timbers.

Source: Wikipedia

Incoming search terms:

different woods for building

Knots in Wood

blogtopia — Tue, 02 Jun 2009 03:48:15 +0000

A knot is a particular type of imperfection in a piece of wood; it will affect the technical properties of the wood, usually for the worse, but may be exploited for artistic effect. In a longitudinally-sawn plank, a knot will appear as a roughly circular "solid" (usually darker) piece of wood around which the grain of the rest of the wood "flows" (parts and rejoins). Within a knot, the direction of the wood (grain direction) is up to 90 degrees different from the grain direction of the regular wood.

In the tree a knot is either the base of a side branch or a dormant bud. A knot (when the base of a side branch) is conical in shape (hence the roughly circular cross-section) with the tip at the point in stem diameter at which the plant’s cambium was located when the branch formed as a bud.

During the development of a tree, the lower limbs often die, but may persist for a time, sometimes years. Subsequent layers of growth of the attaching stem are no longer intimately joined with the dead limb, but are grown around it. Hence, dead branches produce knots which are not attached, and likely to drop out after the tree has been sawn into boards.

In grading lumber and structural timber, knots are classified according to their form, size, soundness, and the firmness with which they are held in place. This firmness is affected by, among other factors, the length of time for which the branch was dead while the attaching stem continued to grow.

Knots materially affect cracking (known in the industry as checking) and warping, ease in working, and cleavability of timber. They are defects which weaken timber and lower its value for structural purposes where strength is an important consideration. The weakening effect is much more serious when timber is subjected to forces perpendicular to the grain and/or tension than where under load along the grain and/or compression. The extent to which knots affect the strength of a beam depends upon their position, size, number, and condition.

A knot on the upper side is compressed, while one on the lower side is subjected to tension. If there is a season check in the knot, as is often the case, it will offer little resistance to this tensile stress. Small knots, however, may be located along the neutral plane of a beam and increase the strength by preventing longitudinal shearing. Knots in a board or plank are least injurious when they extend through it at right angles to its broadest surface. Knots which occur near the ends of a beam do not weaken it. Sound knots which occur in the central portion one-fourth the height of the beam from either edge are not serious defects.

Source: Wikipedia

Water content in Wood

blogtopia — Tue, 02 Jun 2009 03:42:56 +0000

Water occurs in living wood in three conditions, namely: (1) in the cell walls, (2) in the protoplasmic contents of the cells, and (3) as free water in the cell cavities and spaces. In heartwood it occurs only in the first and last forms. Wood that is thoroughly air-dried retains from 8-16% of water in the cell walls, and none, or practically none, in the other forms. Even oven-dried wood retains a small percentage of moisture, but for all except chemical purposes, may be considered absolutely dry.

The general effect of the water content upon the wood substance is to render it softer and more pliable. A similar effect of common observation is in the softening action of water on paper or cloth. Within certain limits, the greater the water content, the greater its softening effect.

Drying produces a decided increase in the strength of wood, particularly in small specimens. An extreme example is the case of a completely dry spruce block 5 cm in section, which will sustain a permanent load four times as great as that which a green (undried) block of the same size will support.

The greatest increase due to drying is in the ultimate crushing strength, and strength at elastic limit in endwise compression; these are followed by the modulus of rupture, and stress at elastic limit in cross-bending, while the modulus of elasticity is least affected.

Source: Wikipedia

Wood

blogtopia — Mon, 01 Jun 2009 09:30:38 +0000

Wood is an organic material; in the strict sense it is produced as secondary xylem in the stems of trees (and other woody plants). In a living tree it conducts water and nutrients to the leaves and other growing tissues, and has a support function, enabling woody plants to reach large sizes or to stand up for themselves. However, wood may also refer to other plant materials with comparable properties, and to material engineered from wood, or wood chips or fiber.

People have used wood for millennia for many purposes, primarily as a fuel or as a construction material for making houses, tools, weapons, furniture, packaging, artworks, and paper. Wood can be dated by carbon dating and in some species by dendrochronology to make inferences about when a wooden object was created. The year-to-year variation in tree-ring widths and isotopic abundances gives clues to the prevailing climate at that time.

Source: Wikipedia

Monocot wood

blogtopia — Mon, 01 Jun 2009 09:28:37 +0000

Structural material that roughly (in its gross handling characteristics) resembles ordinary, ‘dicot’ or conifer wood is produced by a number of monocot plants, and these are also usually called wood. Of these, bamboo, botanically a member of the grass family, has considerable economic importance, larger culms being widely used as a building and construction material in their own right and, these days, in the manufacture of engineered flooring, panels and veneer.

Another major plant group that produce material that often is called wood are the palms. Of much less importance are plants such as Pandanus, Dracaena and Cordyline. With all this material, the structure and composition of the structural material is quite different from ordinary wood.

Source: Wikipedia

Colour in Wood

blogtopia — Mon, 01 Jun 2009 09:26:30 +0000

In species which show a distinct difference between heartwood and sapwood the natural colour of heartwood is usually darker than that of the sapwood, and very frequently the contrast is conspicuous (see section of yew log above). This is produced by deposits in the heartwood of chemical substances, so that a dramatic color difference does not mean a dramatic difference in the mechanical properties of heartwood and sapwood, although there may be a dramatic chemical difference.

Some experiments on very resinous Longleaf Pine specimens indicate an increase in strength, due to the resin which increases the strength when dry. Such resin-saturated heartwood is called "fat lighter". Structures built of fat lighter are almost impervious to rot and termites; however they are very flammable. Stumps of old longleaf pines are often dug, split into small pieces and sold as kindling for fires. Stumps thus dug may actually remain a century or more since being cut. Spruce impregnated with crude resin and dried is also greatly increased in strength thereby.

Since the latewood of a growth ring is usually darker in colour than the earlywood, this fact may be used in judging the density, and therefore the hardness and strength of the material. This is particularly the case with coniferous woods. In ring-porous woods the vessels of the early wood not infrequently appear on a finished surface as darker than the denser latewood, though on cross sections of heartwood the reverse is commonly true. Except in the manner just stated the colour of wood is no indication of strength.

Abnormal discolouration of wood often denotes a diseased condition, indicating unsoundness. The black check in western hemlock is the result of insect attacks. The reddish-brown streaks so common in hickory and certain other woods are mostly the result of injury by birds. The discolouration is merely an indication of an injury, and in all probability does not of itself affect the properties of the wood. Certain rot-producing fungi impart to wood characteristic colours which thus become symptomatic of weakness; however an attractive effect known as spalting produced by this process is often considered a desirable characteristic. Ordinary sap-staining is due to fungous growth, but does not necessarily produce a weakening effect.

Source: Wikipedia